ここから本文です
TWO:Sandy gave in, and as they walked toward the hangar they discussed the stories that had come out in the news about queer, ghostly noises heard by passers-by on the state road late at night, accounts of the fright the estate caretaker had received when he investigated and saw a queer, bluish glow in the place and was attacked by something seemingly uncanny and not human.The little man elected to have a cab. When Bow Street was reached Prout had the satisfaction of finding that all his birds had been netted. He received the warm congratulations of his inspector modestly.
Classification by type of system
1natural circulation external heating pipe type
2natural circulation calandria type
3forced circulation type
4falling-film type
5rising film type
6jacket type
7coil type
Classification by method of operation
1single effect evaporator system
2multiple effect evaporator system
3auto-vapor mechanical compression system
4auto-vapor ejector compression system
5multistage flash system

After taking into consideration of the physical and chemical property of solutions, the desired design conditions, and available utilities, we select the most suitable type of system by utilizing our years of experience and excellent results.
In addition, we can offer designs and manufacturing services that take into careful consideration compactness, energy-efficiency, and automatization.

THREE:Grinding, no doubt, if traced to the principles that lie at the bottom, is nothing more than a cutting process, in which the edges employed are harder than any material that can be made into cutters, the edges firmly supported by being imbedded into a mass as the particles of sand are in grindstones, or the particles of emery in emery wheels.

While standard calandria type evaporation systems are widely used as the typical concentration evaporator by the various food and chemical industries, we have delivered many of those systems as finishing concentration evaporators especially for sugar solutions and starch syrups.

THREE:(1.) How may the arrangement of an establishment affect its earnings?(2.) Why is the arrangement of engineering establishments generally irregular?(3.) Why should an erecting shop be a base of arrangement in engineering establishments?(4.) What are the principal materials consumed in engineering works?(5.) Why is not special experience a safe guide in forming plans of shop arrangement?
  • Enables flexible operation with little influence from variations in load and raw solution concentrations because of an adequate amount of solution being held within the system. These systems are also suitable for batch type burning evaporators.
  • Concentrations can be controlled within product specifications by the cascade control using the concentrations of concentrated solution and the raw solution supply and also by the arithmetic control of raw solution concentrations, etc. (Result for sugar solutions: 75±0.2wt%)
  • High-viscosity solutions and solutions that may crystallize can also be utilized by installing a propeller in the evaporator as a forced circulation system.
THREE:"About my money! No. I shall get that all right. What I am uneasy about is this: How did you know I was coming, and why?"Nothing has been what it seemed to be, he mentally determined. I wish Dick would be careful what he says.

This is a process example of a device that continuously and simultaneously concentrates two types of waste liquid with a single high-efficiency steam compressor.

THREE:By assuming this or any other well-proved example, and estimating larger or smaller shafts by keeping their diameters as the cube root of the power to be transmitted, the distance between bearings as the diameter, and the speed inverse as the diameter, the reader will find his calculations to agree approximately with the modern practice of our best engineers. This is not mentioned to give proportions for shafts, so much as to call attention to accidental strains, such as winding belts, and to call attention to a marked discrepancy between actual practice and such proportions as would be given by what has been called the measured or determinable strains to which shafts are subjected.
  • By evaporating the steam using a mechanical compressor and reusing it, almost no heating steam is alomost required except the time of start-up, so large energy savings can be expected.
  • By combining with a thin film falling heat exchanger that does not raise the boiling point due to the liquid depth, it is possible to utilize the temperature difference of the compressor at the maximum.
  • Since the residence time and heating time are short and the holding amount is small, starting and stopping can be performed in a short time.
  • It will prevent scale adhesion in the can that the evaporator is divided into two parts, and that the supply of the undiluted solution is alternately switched over a fixed period of time to perform heat concentration.